Garage Door Repair Services › Garage Door Spring Replacement
Garage Door Spring Replacement in Overland Park, KS
Springs do the actual work of lifting the door — the opener just guides it. When a spring breaks, the door becomes dangerously heavy and the opener motor takes on load it was never designed to handle. Replacing springs correctly means matching the right wire size, length, and tension to the specific door weight.
Overland Park Garage Door Pros provides garage door spring replacement for homeowners across Overland Park, KS. Call for a free inspection and a written quote before any work begins.
When to Call
When You Need Garage Door Spring Replacement
- You heard a loud bang in the garage and the door won't lift
- The opener strains and hums but the door barely moves
- One spring is visibly separated or has a gap in the coil
- The door falls faster than normal when you release it manually
- Springs have visible rust or corrosion along the coil
- Door was last serviced over seven years ago and springs were original
How It Works
Our Process for Garage Door Spring Replacement
- 1
Safety Check Before Anything Else
A broken spring under tension is dangerous to work around. The tech secures the door and releases any remaining tension from the broken spring before starting the job.
- 2
Door Weight and Spring Measurement
We measure the door height, weight, and existing spring dimensions. Getting those numbers right determines the correct replacement spring — not just any spring that fits the shaft.
- 3
Both Springs Assessed
If one torsion spring broke, the other is the same age and has the same cycle count. We explain why replacing both at once is usually the smarter call.
- 4
Spring Installation and Winding
New springs are installed on the torsion bar and wound to the correct tension for your door weight. This step requires specific tools — it's not something to attempt without them.
- 5
Balance Test
We disconnect the opener and lift the door manually to chest height. A properly balanced door holds position. If it drifts up or falls, tension gets adjusted until it holds.
- 6
Full Cycle Testing
The opener is reconnected and the door runs through multiple cycles. We check travel limits, reversal, and opener effort before calling the job complete.
What's included
- Measurement and selection of correctly rated replacement springs
- Removal of broken spring and safe disposal
- Installation and winding of new springs to proper tension
- Manual balance test before reconnecting the opener
- Opener travel limit and force adjustment after spring installation
- Inspection of cables and drums for damage caused by the spring failure
What's not included
- Cable replacement if cables were damaged when the spring broke — that's priced separately
- Opener repair or replacement if the motor was damaged running against a broken spring
- Painting or rust treatment of the torsion bar or header bracket
Real Situations
Common Scenarios in Overland Park
A homeowner in the Blue Valley area wakes up to a door that won't open — the opener runs but the door doesn't move.
We verify the spring is broken before anything else. Then we measure the existing spring and replace it with the correct rated spring for the door. We won't just grab the closest size — an undersized spring wears out fast and stresses the opener.
A property manager in the Corbin Park area has a rental unit where the tenant reports one of two springs looks 'stretched out and rusty.'
A spring that looks stretched has lost its tension and is close to failure. We replace both springs since they're the same age. We also check whether the rust is surface-level or has weakened the coil wire itself.
A homeowner near Quivira Road replaced one spring themselves two years ago and now the door is uneven when it opens.
Mismatched springs cause uneven lift and can crack panels over time. We assess whether the current springs are the right specs for the door and rebalance or replace as needed.
Overland Park Context
Why this matters in Overland Park
Kansas City's climate puts springs through hard work — cold winters make metal contract and increase brittleness, while humid summers accelerate rust on springs that aren't coated. Many Overland Park homes built in the 1980s and 1990s still have original springs that are well past their rated cycle life. We see a spike in spring failures every November when temperatures drop fast.
Straight Talk
About pricing & scope
Spring pricing varies based on wire gauge, spring diameter, and length — those specs are determined by door weight, not by brand preference. A heavier two-car door needs a different spring than a lightweight single. If cables or drums show damage from the broken spring, that adds to the scope and we'll tell you before we proceed.
What This Fixes
Problems We See in Overland Park
More Garage Door Repair Services
Garage Door Spring Replacement Near You